GET $100 OFF ON YOUR CUSTOM POPUP TENTS, USE PROMO CODE: FIRSTORDER

Table Cover Size Chart (4ft vs 6ft vs 8ft Tables)

Table Cover Size Chart (4ft vs 6ft vs 8ft Tables)

"My table is 6ft, so why doesn't the cover fit?" 

This question is one of the most common sizing questions, and the answer is almost always the same. A table cover is sized to three dimensions, not one. 

Length is the number everyone knows. Height and depth are the ones that make the sides hang wrong, stop short of the floor, or refuse to stretch over the corners.

This table cover size chart starts with your table's dimensions and gives you the cover size, drop and style that actually fit.

Table Cover Size Chart for 4ft, 6ft and 8ft Tables

The chart below uses typical folding and banquet table sizes. A floor-length cover drops the full table height on every side, so its flat size is the table length plus two drops, by the table depth plus two drops.

Table

Typical top (L x D)

Height

Floor-length 4-sided cover (flat)

Lap-length cover (about 15" drop)

4ft

48" x 24"

30"

about 108" x 84"

about 78" x 54"

6ft

72" x 30"

30"

about 132" x 90"

about 102" x 60"

6ft (narrow)

72" x 24"

30"

about 132" x 84"

about 102" x 54"

8ft

96" x 30"

30"

about 156" x 90"

about 126" x 60"

8ft (narrow)

96" x 24"

30"

about 156" x 84"

about 126" x 54"

6ft counter height

72" x 24"

42"

about 156" x 108"

about 102" x 54"

Fitted and stretch covers aren't listed as flat sizes because they're cut to the table itself: length x depth x height. A 6ft fitted cover, for example, is built for a 72" x 30" top at about 30" high.

Cut sizes vary from one maker to another, so always confirm the cover's actual dimensions on your proof before it goes to print.

Why Your "6ft" Cover Doesn't Fit: Three Dimensions

Height

Standard tables sit around 30" high. Counter and bar-height tables sit around 42". A cover cut for a 30" table will stop about a foot above the floor on a 42" table, which shows the legs and anything stored underneath.

Depth

Most 6ft and 8ft tables are 30" deep, but plenty of trade show and display tables are only 24". A fitted or stretch cover made for a 24" top won't pull over a 30" top. Going the other way, a 30" cover on a 24" table leaves about 6" of slack that bunches at the sides.

Drop

Drop is how far the fabric falls below the tabletop. Floor-length, lap-length and tabletop covers are three different products, even for the same table.

How Much Drop Do You Need?

Drop

How far it falls

Best for

Tabletop

No overhang, or a few inches

Branding on top of a bare or covered table, using a table runner or stretch table topper

Lap or mid drop

About 10" to 15"

Seated tables, casual events, tables where legs don't need hiding

Floor length

The full table height, with about 1" of clearance

Trade shows, vendor booths and any table hiding storage


For trade shows, floor length is the norm. It hides boxes and cables and gives your graphics the biggest canvas.

Which Cover Style Fits Which Table?

Table situation

Throw

Fitted

Stretch

Standard 30" height, known size

Works

Works

Works

Depth might be 24" or 30"

Most forgiving

Must match exactly

Must match exactly

Bar or counter height (42")

Needs a longer cut

Needs a bar-height cut

Needs a bar-height cut

Venue table unknown

Safest choice

Risky

Risky

A table throw drapes over the table, so it tolerates small differences. A fitted table cover and a stretch table cover are cut to exact dimensions, so they only fit the table they were made for.

Measure Your Table in 60 Seconds

  1. Length: measure the tabletop end to end. This confirms 4ft, 6ft or 8ft.

  2. Depth: measure front to back. Note whether it's 24" or 30".

  3. Height: measure from the floor to the top of the table. This becomes your floor-length drop.

  4. Back: decide whether staff will sit behind the table (open back) or the table is seen from all sides (closed back).

  5. The real table: if a venue supplies the table, ask for its dimensions or measure it on arrival at your first show.

Write all three numbers down in inches, then order by the cover's dimensions, not the table's name.

Common Sizing Mistakes

  • Ordering by the table's name. "6ft" only tells you the length.

  • Ignoring depth. A 24" cover won't stretch over a 30" top.

  • Using a standard cover on a bar table. It ends about 12" above the floor.

  • Assuming every 6ft table matches. Venues and rental companies use different tables.

  • Sizing up "just in case." An oversized cover pools on the floor and becomes a trip hazard.

Get the Right Fit with Express Canopy

Express Canopy makes custom table covers and throws in 4ft, 6ft and 8ft sizes, in fitted, stretch and throw styles, with 4-sided or 3-sided open-back options. Every order includes a free email proof, so you can check the cover's dimensions before printing. Measure your table, then upload your artwork or send us your table dimensions and we'll help you choose the right size.

Frequently Asked Questions

Can one table cover fit both a 6ft and an 8ft table?

Not if it’s fitted or stretch, since those are cut for one length. A throw won’t work well either way. An 8ft throw on a 6ft table leaves about 12" of extra fabric at each end, which pools on the floor. A 6ft floor-length throw on an 8ft table stops about 12" short at each end, so the legs show. If you use both table sizes, order a cover for each.

What size table does a 90" x 132" tablecloth fit?

It fits a standard 6ft table (72" x 30", 30" high) with a floor-length 30" drop on all four sides. On a 6ft table that’s only 24" deep, the sides hang 33" and pool about 3" on the floor, so an 84" x 132" cover is the better match.

What size table does a 60" x 120" tablecloth fit?

It’s a lap-length cloth for an 8ft table (96" x 30"), with about a 12" drop at the ends and 15" at the sides. That’s a little shorter at the ends than the 126" x 60" size in the chart above, which gives an even 15" all around. On a 6ft table, the ends hang about 24" while the sides stay at 15", so the drop looks uneven.

 


What are you looking for?

Your cart